Description
Downloads
User Manual
Product Overview
Manufacturers Page
Accessories supplied with the unit
Integrated rubber protective frame for increased grip and impact resistance, rear stand and measuring lead holderProtective bag
High-quality silicone measuring leads with gold-plated 2 mm and screw-on 4 mm measuring tip
Wire temperature sensor
Batteries (3 x 1.5 V Micro AAA/ IEC LR03)
- Precise due to true RMS measurement method (TRUE RMS)
- Highest measurement category CAT IV 600 V for maximum protection against overvoltages
- AutoV function for automatic AC/DC voltage detection and low input impedance LoZ to suppress reactive voltages
- Continuity test via buzzer and red LED for noisy environments
- Voltage sensor signals phase voltages and cable breaks in lines without contact (red LED/buzzer)
- Robust housing design thanks to integrated rubber protective frame with magnetic hanger
- Compact protective bag and other accessories included in the scope of delivery
Features
- Backlit digital display with 60,000 digit resolution
- TRUE RMS true RMS measurement (AC and AC+DC) for measuring non-linear signals
- MIN / MAX / average value and fast PEAK recording (250 μs)
- Socket monitoring (optical/acoustic) in the μA/mA and A range with warning in the event of incorrect operation (fuse protection)
- AutoV function for automatic AC/DC switching and measuring range selection
- Low-pass filter (HFR high-frequency suppression, 1000 Hz) for measurements on switched motor drives
- Display HOLD and Auto-HOLD for stable measured value
- Ergonomic 2-component housing for increased grip and shock resistance
Functions
- 1. REL Δ Relative measurement for offset compensation
2. VoltSense (voltage sensor) Non-contact and single-pole phase test with 2 sensitivity levels
3. AUTO-RANGE Automatic measuring range selection for increased ease of use
4. HOLD/ A-HOLD Manual and automatic storage of the display value for convenient reading
5. peak value storage (250 µs) for current and voltage (APO deactivated)
6. resistance/ continuity (Antenna /Lamp) Max. Resolution 0.01 Ω to 60 MΩ Optical and acoustic signal with fast response time (< 100 µs)
7. logic level (Hz/ %) Frequency and duty cycle measurement of logic signals
8. mV DC, AC, AC+DC 0.01 V resolution (600 mV measuring range)
9. V DC, AC+DC 0.03 % basic accuracy VDC (max.)
10. V AC/ HFR Switchable low-pass filter for measurement on frequency converters and noisy signals
11. AutoV Automatic AC+DC switching and measuring range selection
12. LoZ Low input impedance (>2 kΩ) for suppression of “reactive voltages”
13. socket control (optical/acoustic) warning in case of incorrect measuring range selection to protect the fuses
14. robust and ergonomic housing With integrated rubber protection frame, rear stand and test lead holder
15 APO (Auto Power OFF) Automatic switch-off after 30 minutes for extended battery life (can be deactivated)
16. large digital display with 60,000 digit resolution and illumination, rate: 5/s
17th RANGE Automatic and manual measuring range selection
18. analog bargraph for measuring trend determination, rate: 50/ s
19. function / function selection and display illumination (APO 16 min.)
20. Hz Measurement of noisy mains frequencies
21. MIN/ MAX MIN/ MAX/ AVG measured value memory (APO deactivated)
22. 4 mA – 20 mA DC current loop measurement (%) For process signals
23. mA/ A DC, AC, AC+DC For precise TRUE RMS current measurements
24. µA DC, AC, AC+DC Measurement of small currents, e.g. ionization current of a gas heater (HVAC technology)
25. temperature via K-type sensor in °C and °F
26. capacitance/diode measurement of capacitors up to 10 mF, optical and acoustic diode testing
27. safety DIN EN 61010-1, DIN EN 61010-2-033
28. CAT IV 600 V/ CAT III 1000 V transient protection up to 8 kV (1.2 µs/ 50 µs)
29. TRUE RMS AC, AC+DC true RMS measurement method for non-sinusoidal signals
30. 1 kV HBC fuses with high breaking capacity 20 kA@1000 V, F 11 A / 30 kA@1000 V, F 0.4 A
Physically
– Color/Finish redblack
